Crown CTS-3000 #8810

Options
Quantity	1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150
Add to cart
New Price:	$3,354.99 We will beat any price. Seen a better price or want to make us an offer? Click Here. Link to this product.
Details
Building on the foundation of the Crown� Com-Tech� Series, the CTs Series offers new fl exibility and value for installed sound applications. The Com-Tech Series were the fi rst to offer independent selection of highand low-impedance operation for a specifi c channel, and CTs Series amplifi ers continue that tradition, with power levels and features carefully chosen to perfectly integrate into fi xed install design requirements. For added fl exibility, the CTs Series includes both dual-channel and multi-channel models. All models in the CTs Series feature Crown�s new Switching Power Supply for lighter weight, and all models are also compatible with Harman Pro System Architect as well as the IQ System�. Two-channel models accept PIP2� modules, and also feature selectable high-pass fi lters and input sensitivity for each channel. In a profession where unplanned service calls quickly wipe out profi ts, the CTs Series ampli- fi ers are designed to be the most reliable ampli- fi ers you can install. For more details about the Crown CTs Series, contact Crown Customer Service at 800-342- 6939 or 574-294-8200. Also, visit the Crown Audio website at www.crownaudio.com. Specifications Frequency Response (at 1 watt, 20 Hz - 20 kHz): �0.25 dB. Signal to Noise Ratio below rated power (20 Hz to 20 kHz): 105 dB A-weighted. Total Harmonic Distortion (THD) at full rated power, from 20 Hz to 20 kHz: CTs 600/1200: < 0.1%. CTs 2000/3000 < 0.35%. Damping Factor: 10 Hz to 100 Hz: > 3000. Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB. Common Mode Rejection (CMR) (20 Hz to 1 kHz): 50 dB. DC Output Offset: < �2 mV. Input Impedance (nominal): 10 kilohms balanced, 5 kilohms unbalanced. Maximum Input Level: +20 dBu before input compression, +32 dBu absolute maximum. Load Impedance: (Note: Safe with all types of loads) CTs 600/1200 Stereo: 2/4/8/16 ohms, 70V. Bridge Mono: 4/8/16 ohms, 140V. CTs 2000/3000 Stereo: 2/4/8/16 ohms, 70V, 100V. Bridge Mono: 4/8/16 ohms, 140V, 200V. Voltage Gain (at maximum level setting): 8/4 ohm operation, 1.4V sensitivity CTs 600 35:1 (31 dB) CTs 1200 50:1 (34 dB) CTs 2000 63.9:1 (36 dB) CTs 3000 71.4:1 (37 dB) 26 dB: 20:1 (26 dB). 70V operation, 1.4V sensitivity or 100V operation, 2.0V sensitivity: 50:1 (34 dB). Required AC Mains (+15%, �25%): 120V/60 Hz, 230V/50 Hz. Power Draw at Idle (120VAC mains): CTs 600/1200: 24W (standby mode) CTs 2000/3000: 35W (standby mode). Cooling: Continuously variable speed forced air, front-to-back airfl ow. Dimensions: 19 in. (48.3 cm) W x 3.5 in. (8.9 cm) H x 14.25 in. (36.2 cm) D. Front Panel Controls and Indicators Bridge Mode Indicator: Yellow LED illuminates when the rear-panel Mode Switch is set to the �Bridge� position. Ready Indicator: Green LED, one per channel, illuminates when the channel is initialized and ready to produce audio output. Indicator is off when PIP puts the amplifi er in standby mode via the control system. Signal Indicators: Three green LEDs per channel indicate the amplifi er�s input and output signal levels. Signal: input signal is above �40 dBu. �20 dB: amplifi er output is 20 dB below clipping. �10 dB: amplifi er output is 10 dB below clipping. Clip Indicator: Red LED, one per channel, illuminates when the channel�s output signal reaches the onset of audible clipping. The Clip Indicator also will illuminate during Thermal Level Control (TLC) limiting or when the input compressor/limiter is protecting the amplifi er from input overload. Thermal Indicator: Red LED, one per channel, illuminates when the channel has shut down, or is very near shutting down, due to thermal stress or overload. Fault Indicator: Red LED, one per channel, flashes when the amplifier output channel has stopped operating. Data Indicator: Yellow LED indicates control data activity (if the amplifi er is equipped with an IQ-PIP2 module, and connected to a control system). Power Indicator: Blue LED indicates amplifi er has been turned on and AC power is available. The LED will fl ash when the AC line voltage is 15% above or 25% below the nominal rated value. Cooling Vents: Front-to-rear forced airfl ow. Power Switch: Push-on / push-off switch. Back Panel Controls and Connectors Power Cord Connector: Standard 15 amp IEC inlet. Voltage is indicated above IEC inlet. Reset Switch: Resets the circuit breaker that protects the power supply. Speaker Connectors: One four-pole touchproof terminal strip. Accepts up to 10 AWG terminal forks. Input Connectors: Balaced 3-pin terminal block connectors, one per channel, on the standard PIP2-BBY module.